The Product Safety and Metrology etc. (Amendment) Regulations 2024
Write the words of this act the way you think they should read. Solon shows your change as a redline against the published text and pins it to that exact text, so it can never be applied to wording you did not see.
Change 1
12 Amendment to the Simple Pressure Vessels (Safety) Regulations 2016
(1) The Simple Pressure Vessels (Safety) Regulations 2016 are amended as follows. (2) In regulation 2(4), in the definition of “the Directive” omit “(as it has effect immediately before IP completion day)”. (3) For regulation 38C substitute— Further use of the UK marking 38C (1) In this regulation— (a) any reference to an Article or an Annex is a reference to an Article of or an Annex to the Directive; (b) “harmonised standard” has the meaning given to it in Article 2(9). (2) Subject to paragraphs (4) and (5), paragraph (3) applies where, before placing a category A vessel on the market, the manufacturer— (a) ensures that the vessel has been designed and manufactured in accordance with the essential safety requirements set out in Annex I; (b) ensures that the relevant conformity assessment procedures that apply to that vessel in accordance with Article 13(1) and (2) have been carried out; (c) draws up the technical documentation referred to in Annex II; and (d) ensures that the technical documentation and other records and correspondence relating to the conformity assessment procedures are prepared in or translated into English. (3) Where this paragraph applies— (a) the requirements of regulations 4(1) and 5 are to be treated as being satisfied; (b) except for regulation 43, Part 3 does not apply; (c) regulations 2(5)(a), 6, 8, 9(2), 16(2), 18(a) and (b), 19(1), 23, 26, 30, 32, 38(1) and 62 apply subject to the modifications in paragraph (6); (d) regulation 43 and Schedule 3 apply subject to the modifications in paragraphs (6) and (7). (4) This paragraph applies where there is no designated standard or part of a designated standard which corresponds exactly to a harmonised standard or part of a harmonised standard referred to in Article 12. (5) Where paragraph (4) applies, paragraph (2)(b) is to be treated as requiring the manufacturer to have carried out— (a) the conformity assessment procedure set out in Article 13(1)(b); and (b) the relevant conformity assessment procedure that applies to that product in accordance with Article 13(2). (6) The modifications referred to in paragraph (3)(c) and (d) are that— (a) any reference to “essential safety requirements” is to be read as a reference to the essential safety requirements referred to in Annex I; (b) any reference to “designated standard” is to be read as a reference to a harmonised standard; (c) any reference to “relevant conformity assessment procedure” is to be read as a reference to the relevant conformity assessment procedure that applies to the vessel in accordance with Article 13(1) and (2); (d) any reference to “technical documentation” is to be read as a reference to the technical documentation referred to in Annex II. (7) The modifications referred to in paragraph (3)(d) are that— (a) in regulation 43, the reference to Schedule 2 is to be read as a reference to Annex II; (b) in Schedule 3— (i) in paragraph 5 the reference to “relevant statutory requirements” is to be read as including the Directive; (ii) in paragraph 7 the reference to “approved body” is to be read as a reference to the conformity assessment body that undertook the relevant conformity assessment procedure in accordance with Article 13(1) or 13(2). . (4) In regulation 76A, omit paragraphs (4) to (6).
12 Amendment to the Simple Pressure Vessels (Safety) Regulations 2016
(1) The Simple Pressure Vessels (Safety) Regulations 2016 are amended as follows. (2) In regulation 2(4), in the definition of “the Directive” omit “(as it has effect immediately before IP completion day)”. (3) For regulation 38C substitute— Further use of the UK marking 38C (1) In this regulation— (a) any reference to an Article or an Annex is a reference to an Article of or an Annex to the Directive; (b) “harmonised standard” has the meaning given to it in Article 2(9). (2) Subject to paragraphs (4) and (5), paragraph (3) applies where, before placing a category A vessel on the market, the manufacturer— (a) ensures that the vessel has been designed and manufactured in accordance with the essential safety requirements set out in Annex I; (b) ensures that the relevant conformity assessment procedures that apply to that vessel in accordance with Article 13(1) and (2) have been carried out; (c) draws up the technical documentation referred to in Annex II; and (d) ensures that the technical documentation and other records and correspondence relating to the conformity assessment procedures are prepared in or translated into English. (3) Where this paragraph applies— (a) the requirements of regulations 4(1) and 5 are to be treated as being satisfied; (b) except for regulation 43, Part 3 does not apply; (c) regulations 2(5)(a), 6, 8, 9(2), 16(2), 18(a) and (b), 19(1), 23, 26, 30, 32, 38(1) and 62 apply subject to the modifications in paragraph (6); (d) regulation 43 and Schedule 3 apply subject to the modifications in paragraphs (6) and (7). (4) This paragraph applies where there is no designated standard or part of a designated standard which corresponds exactly to a harmonised standard or part of a harmonised standard referred to in Article 12. (5) Where paragraph (4) applies, paragraph (2)(b) is to be treated as requiring the manufacturer to have carried out— (a) the conformity assessment procedure set out in Article 13(1)(b); and (b) the relevant conformity assessment procedure that applies to that product in accordance with Article 13(2). (6) The modifications referred to in paragraph (3)(c) and (d) are that— (a) any reference to “essential safety requirements” is to be read as a reference to the essential safety requirements referred to in Annex I; (b) any reference to “designated standard” is to be read as a reference to a harmonised standard; (c) any reference to “relevant conformity assessment procedure” is to be read as a reference to the relevant conformity assessment procedure that applies to the vessel in accordance with Article 13(1) and (2); (d) any reference to “technical documentation” is to be read as a reference to the technical documentation referred to in Annex II. (7) The modifications referred to in paragraph (3)(d) are that— (a) in regulation 43, the reference to Schedule 2 is to be read as a reference to Annex II; (b) in Schedule 3— (i) in paragraph 5 the reference to “relevant statutory requirements” is to be read as including the Directive; (ii) in paragraph 7 the reference to “approved body” is to be read as a reference to the conformity assessment body that undertook the relevant conformity assessment procedure in accordance with Article 13(1) or 13(2). . (4) In regulation 76A, omit paragraphs (4) to (6).
One line that says what changes, such as "Halve the dog tax".
Who it helps, what it costs, what it fixes. It is what persuades people to support it.
How this law is officially changed
Solon does not know this law's official route yet. The proposal is recorded all the same, and the route appears here once its source is added.
A proposal here is not law. Support on Solon is evidence that people want the change; the official route says what it takes to make it law.
Sign in to file your proposal. What you have written stays on this page.
Sign in to file itThink it through
Ask what your change would do, who would gain and who would bear a cost, and where something like it is already law. The assistant reads your draft as it stands, cites the law and the studies it finds, and takes no side. What you file stays yours.