The Product Safety and Metrology etc. (Amendment) Regulations 2024
Write the words of this act the way you think they should read. Solon shows your change as a redline against the published text and pins it to that exact text, so it can never be applied to wording you did not see.
Change 1
22 Amendment to the Gas Appliances (Enforcement) and Miscellaneous Amendments Regulations 2018 and Regulation (EU) 2016/426
(1) The Gas Appliances (Enforcement) and Miscellaneous Amendments Regulations 2018 are amended as follows. (2) For regulation 2C substitute— Further use of UK marking 2C (1) In this regulation “harmonised standard” has the meaning given to it in Article 2(23) of Regulation 2016/426 (pre-exit). (2) Paragraph (3) applies where, before placing an appliance or fitting on the market or using an appliance for their own purposes, the manufacturer— (a) ensures that the appliance or fitting has been designed and manufactured in accordance with the essential requirements set out in Annex I to Regulation 2016/426 (pre-exit); (b) carries out the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit) or has it carried out; (c) draws up the technical documentation referred to in Annex III to Regulation 2016/426 (pre-exit); and (d) ensures that the technical documentation and other records and correspondence relating to the conformity assessment procedure are prepared in or translated into English. (3) Where this paragraph applies— (a) Article 7(1) and the first subparagraph of Article 7(2) are to be treated as being satisfied; (b) Articles 13, 14 and 17(3) do not apply; (c) the following provisions of Article 7 apply subject to the modifications in paragraph (4)— (i) Article 7(2), second subparagraph; (ii) Article 7(3); (iii) Article 7(4); (d) Articles 8, 9(2), (4), (5) and (8), 10(2) and (3), 15(1) to (4), 17(4) and 40(1) and Annex V apply subject to the modifications in paragraph (4). (4) The modifications referred to in paragraph (3)(c) and (d) are that— (a) any reference to “essential requirements” is to be read as a reference to the essential requirements set out in Annex I to Regulation 2016/426 (pre-exit); (b) any reference to “designated standard” is to be read as a reference to a harmonised standard; (c) any reference to “technical documentation” is to be read as a reference to the technical documentation referred to in Annex III to Regulation 2016/426 (pre-exit); (d) in Article 7(2), in the second subparagraph the reference to “procedure referred to in the first subparagraph” is to be read as a reference to the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit); (e) any reference to “appropriate conformity assessment procedure” is to be read as a reference to the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit); (f) Article 17(4) is to be read as if the words beginning with “and” and ending with “paragraph 3” were omitted; (g) in Annex 5 the reference to “relevant statutory requirements” is to be read as including Regulation 2016/426 (pre-exit); (h) in paragraph 7 of Annex 5, the reference to “approved body” is to be read as a reference to the conformity assessment body that undertook the conformity assessment procedure in accordance with Article 14 of Regulation 2016/426 (pre-exit). . (3) In Article 44 of Regulation (EU) 2016/426 of the European Parliament and of the Council on appliances burning gaseous fuels and repealing Directive 2009/142/EC, omit paragraphs (4) to (6).
22 Amendment to the Gas Appliances (Enforcement) and Miscellaneous Amendments Regulations 2018 and Regulation (EU) 2016/426
(1) The Gas Appliances (Enforcement) and Miscellaneous Amendments Regulations 2018 are amended as follows. (2) For regulation 2C substitute— Further use of UK marking 2C (1) In this regulation “harmonised standard” has the meaning given to it in Article 2(23) of Regulation 2016/426 (pre-exit). (2) Paragraph (3) applies where, before placing an appliance or fitting on the market or using an appliance for their own purposes, the manufacturer— (a) ensures that the appliance or fitting has been designed and manufactured in accordance with the essential requirements set out in Annex I to Regulation 2016/426 (pre-exit); (b) carries out the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit) or has it carried out; (c) draws up the technical documentation referred to in Annex III to Regulation 2016/426 (pre-exit); and (d) ensures that the technical documentation and other records and correspondence relating to the conformity assessment procedure are prepared in or translated into English. (3) Where this paragraph applies— (a) Article 7(1) and the first subparagraph of Article 7(2) are to be treated as being satisfied; (b) Articles 13, 14 and 17(3) do not apply; (c) the following provisions of Article 7 apply subject to the modifications in paragraph (4)— (i) Article 7(2), second subparagraph; (ii) Article 7(3); (iii) Article 7(4); (d) Articles 8, 9(2), (4), (5) and (8), 10(2) and (3), 15(1) to (4), 17(4) and 40(1) and Annex V apply subject to the modifications in paragraph (4). (4) The modifications referred to in paragraph (3)(c) and (d) are that— (a) any reference to “essential requirements” is to be read as a reference to the essential requirements set out in Annex I to Regulation 2016/426 (pre-exit); (b) any reference to “designated standard” is to be read as a reference to a harmonised standard; (c) any reference to “technical documentation” is to be read as a reference to the technical documentation referred to in Annex III to Regulation 2016/426 (pre-exit); (d) in Article 7(2), in the second subparagraph the reference to “procedure referred to in the first subparagraph” is to be read as a reference to the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit); (e) any reference to “appropriate conformity assessment procedure” is to be read as a reference to the applicable conformity assessment procedure referred to in Article 14 of Regulation 2016/426 (pre-exit); (f) Article 17(4) is to be read as if the words beginning with “and” and ending with “paragraph 3” were omitted; (g) in Annex 5 the reference to “relevant statutory requirements” is to be read as including Regulation 2016/426 (pre-exit); (h) in paragraph 7 of Annex 5, the reference to “approved body” is to be read as a reference to the conformity assessment body that undertook the conformity assessment procedure in accordance with Article 14 of Regulation 2016/426 (pre-exit). . (3) In Article 44 of Regulation (EU) 2016/426 of the European Parliament and of the Council on appliances burning gaseous fuels and repealing Directive 2009/142/EC, omit paragraphs (4) to (6).
One line that says what changes, such as "Halve the dog tax".
Who it helps, what it costs, what it fixes. It is what persuades people to support it.
How this law is officially changed
Solon does not know this law's official route yet. The proposal is recorded all the same, and the route appears here once its source is added.
A proposal here is not law. Support on Solon is evidence that people want the change; the official route says what it takes to make it law.
Sign in to file your proposal. What you have written stays on this page.
Sign in to file itThink it through
Ask what your change would do, who would gain and who would bear a cost, and where something like it is already law. The assistant reads your draft as it stands, cites the law and the studies it finds, and takes no side. What you file stays yours.