The Product Safety and Metrology etc. (Amendment) Regulations 2024
Write the words of this act the way you think they should read. Solon shows your change as a redline against the published text and pins it to that exact text, so it can never be applied to wording you did not see.
Change 1
5 Amendment to the Aerosol Dispensers Regulations 2009
(1) The Aerosol Dispensers Regulations 2009 are amended as follows. (2) For regulation 5A substitute— Obligations that are met by complying with obligations in the Directive 5A (1) In this regulation any reference to an Article or an Annex is a reference to an Article or an Annex of the Directive. (2) Paragraph (5) sets out the requirements which must be complied with in order to mark an aerosol dispenser with the UK marking. (3) Paragraphs (5) and (6) set out the requirements which must be complied with under regulation 5(a)(ii)(aa) in order to mark an aerosol dispenser with the symbol “3” (inverted epsilon). (4) Where the requirements in paragraph (5) are complied with— (a) the requirements of regulation 3(1) are disapplied; (b) the requirements of regulation 3(2) to (7) are treated as being satisfied; (c) the reference in regulation 5(a)(i) to regulation 3 is to be read as a reference to paragraph (5) and regulation 3(8) and (9). (5) The requirements referred to in paragraphs (2) and (3) are that— (a) the aerosol dispenser is a relevant aerosol dispenser; (b) the relevant aerosol dispenser— (i) complies with the provisions relating to construction and equipment set out in point 2.1 of the Annex; (ii) complies with the provisions relating to the volume of the liquid phase set out in point 2.3 of the Annex; (iii) complies with the special provision set out in points 3, 4 and 5 of the Annex in the case of metal, glass and plastic dispensers respectively; (iv) meets the tests specified in point 6.1.1 of the Annex in the case of empty containers; (v) meets the test specified in point 6.1.2 and 6.1.3 of the Annex in the case of empty metal and protected glass dispensers respectively; and (vi) satisfies one of the following paragraphs— (aa) it meets the test methods specified in point 6.1.4.1(a) of the Annex and the dispenser is not of a type referred to in point 6.1.4.2 of the Annex; (bb) it meets the test method specified in point 6.1.4.1(b) of the Annex and the dispenser is not of a type referred to in point 6.1.4.2 of the Annex; (cc) it meets the test method specified in point 6.1.4.1(c) of the Annex; (c) the person responsible for the marketing of the relevant aerosol dispenser has complied with the obligations set out after the heading to point 2 (general provisions) and immediately before point 2.1 in the Annex. (6) The requirements referred to in paragraph (3) are that— (a) the relevant aerosol dispenser— (i) complies with the requirements of Article 8(1) (or where permitted by that Article, its label complies with those requirements); (ii) complies with the requirements of Article 8(1a); (iii) bears, or where permitted by Article 8(1), has on its label the information required by Article 8(1)(d) and 8(1a) prepared in or translated into English; and (b) the person responsible for the marketing of the relevant aerosol dispenser has affixed the symbol “3” (inverted epsilon) in accordance with Article 3. .
5 Amendment to the Aerosol Dispensers Regulations 2009
(1) The Aerosol Dispensers Regulations 2009 are amended as follows. (2) For regulation 5A substitute— Obligations that are met by complying with obligations in the Directive 5A (1) In this regulation any reference to an Article or an Annex is a reference to an Article or an Annex of the Directive. (2) Paragraph (5) sets out the requirements which must be complied with in order to mark an aerosol dispenser with the UK marking. (3) Paragraphs (5) and (6) set out the requirements which must be complied with under regulation 5(a)(ii)(aa) in order to mark an aerosol dispenser with the symbol “3” (inverted epsilon). (4) Where the requirements in paragraph (5) are complied with— (a) the requirements of regulation 3(1) are disapplied; (b) the requirements of regulation 3(2) to (7) are treated as being satisfied; (c) the reference in regulation 5(a)(i) to regulation 3 is to be read as a reference to paragraph (5) and regulation 3(8) and (9). (5) The requirements referred to in paragraphs (2) and (3) are that— (a) the aerosol dispenser is a relevant aerosol dispenser; (b) the relevant aerosol dispenser— (i) complies with the provisions relating to construction and equipment set out in point 2.1 of the Annex; (ii) complies with the provisions relating to the volume of the liquid phase set out in point 2.3 of the Annex; (iii) complies with the special provision set out in points 3, 4 and 5 of the Annex in the case of metal, glass and plastic dispensers respectively; (iv) meets the tests specified in point 6.1.1 of the Annex in the case of empty containers; (v) meets the test specified in point 6.1.2 and 6.1.3 of the Annex in the case of empty metal and protected glass dispensers respectively; and (vi) satisfies one of the following paragraphs— (aa) it meets the test methods specified in point 6.1.4.1(a) of the Annex and the dispenser is not of a type referred to in point 6.1.4.2 of the Annex; (bb) it meets the test method specified in point 6.1.4.1(b) of the Annex and the dispenser is not of a type referred to in point 6.1.4.2 of the Annex; (cc) it meets the test method specified in point 6.1.4.1(c) of the Annex; (c) the person responsible for the marketing of the relevant aerosol dispenser has complied with the obligations set out after the heading to point 2 (general provisions) and immediately before point 2.1 in the Annex. (6) The requirements referred to in paragraph (3) are that— (a) the relevant aerosol dispenser— (i) complies with the requirements of Article 8(1) (or where permitted by that Article, its label complies with those requirements); (ii) complies with the requirements of Article 8(1a); (iii) bears, or where permitted by Article 8(1), has on its label the information required by Article 8(1)(d) and 8(1a) prepared in or translated into English; and (b) the person responsible for the marketing of the relevant aerosol dispenser has affixed the symbol “3” (inverted epsilon) in accordance with Article 3. .
One line that says what changes, such as "Halve the dog tax".
Who it helps, what it costs, what it fixes. It is what persuades people to support it.
How this law is officially changed
Solon does not know this law's official route yet. The proposal is recorded all the same, and the route appears here once its source is added.
A proposal here is not law. Support on Solon is evidence that people want the change; the official route says what it takes to make it law.
Sign in to file your proposal. What you have written stays on this page.
Sign in to file itThink it through
Ask what your change would do, who would gain and who would bear a cost, and where something like it is already law. The assistant reads your draft as it stands, cites the law and the studies it finds, and takes no side. What you file stays yours.